How Much Weight Can 1 Inch Hook Screws Hold Ceiling How To Measure, Install and Maintain Roller Window Blinds

You are searching about How Much Weight Can 1 Inch Hook Screws Hold Ceiling, today we will share with you article about How Much Weight Can 1 Inch Hook Screws Hold Ceiling was compiled and edited by our team from many sources on the internet. Hope this article on the topic How Much Weight Can 1 Inch Hook Screws Hold Ceiling is useful to you.

How To Measure, Install and Maintain Roller Window Blinds

Roller blinds – How to measure

Introduction

There are a number of things to consider when measuring for new blinds. Below is a quick guide to help you. First, make sure you have a pencil and some paper and a tape measure (preferably a metal one).

What to measure in

Always measure in millimeters (mm), as most roller blind suppliers require a size in millimeters.

Where to measure

In normal window areas there are 2 potential places for your blinds to be installed, these are known as the window face or the window recess. Roller blinds can be fitted to the front of your window frame or wall or at the top of the window recess. This gives you full control over the placement of your blind.

For an indentation measurement:

Make sure you have enough depth to mount the inside of the window frame. 75mm should be fine; less will result in the blind sticking out of the recess. If you have less than 75mm, it may be worth considering installing your blind outside the window recess as a face fit.

1) Measure the width of the recess from wall to wall at the top. This is where the brackets must be mounted. Be sure to measure across 3 areas of the width to ensure that the area is the same width (or very similar) and that the walls do not have dents that will affect the function of the blind.

2) Note the shortest measurement.

3) Take 10mm off each side – this will give you some flexibility in case of any variations in your walls and will ensure that your roller blind is not damaged. If you want total light blocking outside, we suggest you adapt your blind to the window.

4) Measure the drop by taking the measurement from the top of the recess to the bottom.

5) Note the shortest measurement.

A stopper is provided with many roller blinds, which means you can limit the movement of the roller blind to ensure it stretches down to fit perfectly on your windowsill. Operate the blind chain with one hand and with the other pinch one of the chain balls between your thumb and forefinger and calculate when it reaches the top of the mechanism. Once you’ve worked out your perfect length, clamp the blind chain stopper onto the chain with pliers.

For a facial measurement:

1) Measure the exact width of where you would like your blind to be. As a guide add an overlap from the window frame of between 50 and 100mm, this will help reduce the gap on the side of the blind, providing better light control and more privacy.

2) Record the measurement.

3) Measure the drop from the top of where you want your blind placed to the bottom.

4) Record the measurement.

And remember…

• Make sure that you have subtracted 10 mm from each side on all recess width measurements.

• Measure at least twice to ensure there are no errors.

• Note the side you want the controls to be so they are easily accessible.

• To be sure of a good fit, it is important that you take any obstacles such as window handles into account when measuring.

• For full-length windows, we recommend that you measure to approx. 20 mm from the floor. This will provide sufficient space and give the blind room to settle overtime.

• Remember to raise the blind 100-150mm above the frame for face fit fitting to allow the roller mechanism to clear as much glass as possible when raised. This will allow more light into the room and is important when blinds are on doors to allow clearance.

• Decide whether the blind is above the roll or under the roll, i.e. is the substance to roll off the front of the tube or the back. The fabric that rolls off the back is generally the standard roll.

Other installation considerations

Low threshold depth (recessed bracket):

It requires approx. 50 mm minimum frame depth to attach all brackets as the minimum depth required for a flush mounting (where the product does not protrude into the room). If your frame depth does not cover this, you should probably consider a face fit installation.

Corner windows:

When two meet in a corner or in a corner where there is only glass, there can be a privacy issue. This is due to a gap where the products fit together. To minimize the problem, consider having one product bypass the other and then specify that the second product fits inside the first.

French doors:

The wider and higher you list your product, the better your privacy, insulation and light control. You will need approx. 100 mm (width) x 50 mm (drop) additional per roller blind for the mounting brackets at the top. This taller and wider measurement means that when the blind is raised, it blocks your view less.

For the width, you should also add at least 30 mm on both sides of the glass. However, the door handles may limit the width you prefer. Ideally, the roller blind should fall just inside the door handle.

Roller blinds can be mounted on either wooden or metal doors. For metal doors, use “metal screws” designed for fastening to metal doors.

Sliding doors:

All our blinds can be specified to be fitted either inside the door frame (RECESS) or above it on the wall (FACE). When deciding this, be sure to measure to see if the handle is an obstruction.

For an external installation, it is usually sufficient to measure approx. 100 mm wider on both sides. The wider you specify, the better your privacy, insulation and light control. For the height, approx. 50 mm above the top of the frame.

Roller blinds – How to install

Introduction

Roller blinds are easy to install and we are confident that it will not take up too much of your time. Be sure to read all the instructions below.

You will need:

1) Drilling machine

2) Boron

3) Phillips screwdriver (the one with the crossed head)

4) Flat screwdriver

5) Box with screws

6) A pencil

How to attach your fittings in…

Concrete, brick or plaster:

If you are drilling in concrete, brick or plaster, use a masonry drill with a diameter of 5.0 mm. You will also need wall plugs and 1 inch Phillips screws (8 gauge).

Wood or steel:

If you are drilling in wood or steel, you should use a high-speed steel drill with a diameter of 3 mm. Often in wood, you can fasten the screws in the wood without having to pre-drill.

Tiles:

If you are drilling into tiles, cover your drill point with masking tape. This will prevent the drill bit from slipping.

1) Gather your tools and unpack your blind.

2) Remove the blind from the package and locate the mounting brackets supplied as a pair. Take a look at your blind and see which side you ordered the control to be on.

3) One bracket is used with the control side of the blind (chain side) and the other bracket is used with the rotator side (see diagram 5).

4) The installation brackets are always mounted so that the inner surfaces face each other. It is very important that the brackets are installed so that the blind is level when installed.

5) Decide where you want the blind placed. The fittings can be placed in 3 different ways:

Inside the frame (recess fit) mounted on the side of the window recess.

Inside the frame (recess fit) fitted to the top (ceiling) of the window recess.

Outside the window frame (face fit).

6) Mark your drill holes with a pencil using the blind brackets supplied as hole templates. Make sure the brackets are completely level so the blind rolls straight up and down.

7) Drill your holes and then screw the brackets into place.

8) Just clip the blind into place by inserting the opposite side of the chain first and then clipping the chain side in

Safety first! Childproof chain guide:

It is a requirement of Australian child safety laws that the blind chain must be attached to the wall or window area using the supplied chain guides. With the chain guide securely in place and holding the chain, you can prevent any risk of strangulation, especially if the chain is lower than 1.6m from the floor. Also, to maintain child safety standards, be sure to keep furniture and cribs away from blind chains.

To attach, hook the chain into the unit and mount to the front of your window area or inside the recess. Mount the unit slightly away from the blind so that it does not interfere with operation.

The secured chain guide must allow the chain to have some slack but not be able to form a loop of more than 220mm. Too much tension will make the blind difficult to operate. The chain must run freely through the chain guide.

Troubleshooting / common problems

The blind has a fold or crease in the fabric…

If the blind has a small fold or crack, it may be due to transport. Blind fabric needs to set, and often small imperfections will correct themselves. The blind’s natural weight and hanging means that small folds or kinks should fall out after a short time. Warm weather helps this process.

In addition to this, blinds that are left in one position for long periods of time can result in the fabric holding a crease or a kink in the fabric. Again, this will decrease over time. If the blind is regularly rotated in different positions, this will help to eliminate this problem.

The blind does not work smoothly…

When you pull the chain to operate your blind, if you feel tight and the blind does not roll smoothly and makes noise, it is most likely that the location of the chain drive end of the blind is in the wrong position. Check the end cap where the gap for the chain should be at the bottom, make sure the cap is not twisted out of position.

The blind does not sit comfortably between the brackets…

The blind must fit snugly between the brackets, if there is up to 4mm of play between the roller blind and the brackets, this can be taken up by turning the knurled wheel clockwise until it locks into place. This extends the pin out.

If the play is more than 4 mm, we suggest either bending the brackets in slightly, no more than approx. 3 mm on each side.

If there is more play than that, one or both brackets must move closer together.

Also, if you find it too tight to clamp the blind in place, try bending the brackets out a little, no more than 3mm on each side. If this is not enough, one or both brackets must be moved closer together.

The blind does not roll up and down properly…

If the fabric rolls off to one side, this can often be fixed by straightening the fabric by pulling it across to the correct position by hand, if that doesn’t work…

Then you can try to enlarge the diameter of the tube on the side from which the fabric rolls away. Roll out the blind to reveal the tube. Place some tape, preferably masking tape, on the corner of the side that the fabric is rolling away from. Sometimes a few pieces of tape are needed, which need to be placed on top of each other to build up enough thickness. You may need to repeat this process a few times until you achieve the perfect roll.

If this does not work, the bracket usually needs to be lowered slightly to overcome the problem. It can be 5 – 10 mm, usually because the head of the window is not flat.

Roller blinds – How to maintain

Cleaning…

Cleaning the roller blind requires only a damp cloth. Be careful not to rub the blind too hard when cleaning, as you can damage either the coating or discolor the blind.

Removing blinds…

If you would like to take down your roller blind, simply turn the clear plastic wheel in the pin end of the blind. This will release the pin from the bracket. Make sure you have a secure grip on the curtain so it doesn’t fall down – ideally get someone to help you do this.

Blind damage…

If your curtain is damaged, many of the component parts can be replaced cheaply. Return to your supplier for spare parts. Common replacement parts include the bottom rail and chain. The bottom rail may need to be replaced with something more complicated, so we recommend that you send it back to your supplier for rework.

If you need to replace the chain, it is a fairly easy process. First remove the blind from the brackets and remove the chain drive from the tube. Loosen the small screw in the center of the chain drive, do not remove it completely. Once it’s loosened, you can pull the end cap forward enough to free the chain from the sprockets. Add your new chain and then tighten the screw and put the end cap back in place.

Changing the chain control page…

If you decide you want the chain control on the opposite side, remove the end caps and switch to opposite sides. Also change the bracket positions.

Video about How Much Weight Can 1 Inch Hook Screws Hold Ceiling

You can see more content about How Much Weight Can 1 Inch Hook Screws Hold Ceiling on our youtube channel: Click Here

Question about How Much Weight Can 1 Inch Hook Screws Hold Ceiling

If you have any questions about How Much Weight Can 1 Inch Hook Screws Hold Ceiling, please let us know, all your questions or suggestions will help us improve in the following articles!

The article How Much Weight Can 1 Inch Hook Screws Hold Ceiling was compiled by me and my team from many sources. If you find the article How Much Weight Can 1 Inch Hook Screws Hold Ceiling helpful to you, please support the team Like or Share!

Rate Articles How Much Weight Can 1 Inch Hook Screws Hold Ceiling

Rate: 4-5 stars
Ratings: 2787
Views: 88913502

Search keywords How Much Weight Can 1 Inch Hook Screws Hold Ceiling

How Much Weight Can 1 Inch Hook Screws Hold Ceiling
way How Much Weight Can 1 Inch Hook Screws Hold Ceiling
tutorial How Much Weight Can 1 Inch Hook Screws Hold Ceiling
How Much Weight Can 1 Inch Hook Screws Hold Ceiling free
#Measure #Install #Maintain #Roller #Window #Blinds

Source: https://ezinearticles.com/?How-To-Measure,-Install-and-Maintain-Roller-Window-Blinds&id=6964509

Related Posts

default-image-feature

How Much Water Weight Can You Retain During Your Period Fast Fat Loss – Simple and Effective Tips

You are searching about How Much Water Weight Can You Retain During Your Period, today we will share with you article about How Much Water Weight Can…

default-image-feature

How Much Weight Can My 5 6 Fly Rod Hold Fly Fishing Tackle Review: Greys GX500 Fly Fishing Reel

You are searching about How Much Weight Can My 5 6 Fly Rod Hold, today we will share with you article about How Much Weight Can My…

default-image-feature

How Much Weight Can You Lose Drinking Aloe Vera Juice Discovering Aloe Vera Juice Benefits

You are searching about How Much Weight Can You Lose Drinking Aloe Vera Juice, today we will share with you article about How Much Weight Can You…

default-image-feature

How Much Weight Can You Lose Drink Apple Cider Vinegar The Essential PCOS Cleanse for Weight Loss

You are searching about How Much Weight Can You Lose Drink Apple Cider Vinegar, today we will share with you article about How Much Weight Can You…

default-image-feature

How Much Weight Can Lose Biking 1 Mile Per Day Seven Seven-Minute Ways to Lose 7.7 KG in 7.77 Days

You are searching about How Much Weight Can Lose Biking 1 Mile Per Day, today we will share with you article about How Much Weight Can Lose…

default-image-feature

How Much Water Weight Can You Lose In Peak Week High School Wrestling: Peaking for the End of the Season

You are searching about How Much Water Weight Can You Lose In Peak Week, today we will share with you article about How Much Water Weight Can…